Clipsal 56011 Especificações descarregar pdf (Página 19)

M1 Serial Port (RS-232) Expander, Thermostat/Lighting Interface

Additional serial port(s) for M1 Controls to interface other manufacturer’s

equipment utilizing RS-232 ASCII commands.

• Adapts HVAC Communicating

Thermostats to M1 Controls

• Allows M1 Controls to interface with

CentraLite & ALC lighting systems

• Adjustable baud rate 300 to 38,400

• Up to 7 M1XSP Expanders may be

added to M1 controls

• Operating Voltage: 12 Volts DC

• Current Draw: 31mA

• Housing Size: 4.375" x 3" x 1.125"

• Circuit Board Size: 3.5" x 2.75"

Some Partner Manufacturers; such as AMX, Control 4, and Crestron,

interface through the main serial port. Visit www.elkproducts.com for

more details and a complete list of partner manufacturers.

ELK-M1XSP

7 62158 55020

Ethernet to RS-232 Serial Bridge

The ELK-IP232 may be used to connect any standard serial communications device to an Ethernet

network. It is able to both initiate and accept network connections. Once a network connection is made,

the remote networked device is virtually connected to the serial device on the other side of the Bridge.

Both the network device and the serial device can send and receive messages to and from each other.

• Supports both UDP and TCP protocols

• Up to 12 simultaneous TCP-IP connections

• Up to twelve (12) "Rules" may be programmed

to make outgoing connections.

• Selectable baud rate from 300 to 115200 baud

• 802.3 compliant 10/100 Mbit interface

• Software and Hardware Handshaking

• Operating Voltage: 12 Volts D.C.

• Current Draw: Approx. 135 mA

• Dimensions: 3.85” L x 1.7”W x 0.93” D

• RS-232, DB9M 9-pin serial port connection

• RJ45 8-pin Network Jack

• LED Indicators for Power, Link, and Data

• Includes: Serial Cable and 12V Supply

7 62158 55064 5

ELK-IP232

NESS Square D/Clipsal C-Bus Interface for M1 Controls

Designed and built by Ness Products, this interface is intended for connecting an

ELK-M1 control to a Clipsal C-Bus Lighting and Control Network.

• Controls up to 255 individual C-Bus

lights or outputs.

• True 2 way communications on the

C-Bus network

• Operating Voltage: 12 Volts D.C.

• Current Draw: Max 60 mA

(Stand by 30 mA)

• Board Size: 4.33” x 4.53” x .9”

ELK-101236

7 62158 55070 6

UPB Interface for M1G & M1EZ8 Controls

The ELK-M1PCSPIM is a special Powerline Interface Module containing a built-in M1XSP Serial Port

chip. This all-in-one device makes it easy to permanently connect the ELK M1 Control to a UPB network.

• Compact, space saving interface

• Easy hookup -- 4-wire data bus connection

• NO 9-Pin Serial Cable Required

• UPB Status light (multicolored)

• M1 Data Bus Status Light (Green)

• Lower cost than purchasing separate and

M1XSP and PCSPIM products.

• Removable 4-pin terminal block connection

• Power:

- UPB Network circuitry – powered from the

AC “Primary” Line.

- M1 Data Bus Device circuitry – powered

(12VDC) from the M1 Data Bus

• Current Draw from M1: ~30mA @ 12 VDC

• M1 Bus Device Address: Preset at Address #7

• Firmware required: Standard Version

(1.0.42 or later)

7 62158 55073 7

ELK-M1PCSPIM

Supervised Remote Power Supply

The ELK-P212S is a Supervised Remote Power Supply/Battery Charger, providing 12 VDC output with

up to 2 Amps of total current. It supervises the AC Power Input as well as the rechargeable Battery, and

can report abnormal conditions back to an ELK-M1 Control over the RS-485 four (4) wire data bus. It

also features relay outputs for AC and Low Battery to allow “stand-alone” operation with other controls.

• M1 Control allows:

- Remote power reset of powered peripherals

- Data-bus supervision of AC and Battery status

• Stand-alone exibility

- Two (2) sets of DC outputs

- On-board relay to supervise battery status

- On-board relay to supervise AC status

• Master AC and Battery ON / OFF Power Switch

• Visual AC Power Indicator

• AC Input: 16.5VAC, 45VA (TRG1640 or equiv.)

• DC Output Voltage: 13.8 Volts D.C. +/- 5%

• Current Rating: 2.0 Amps

• Wattage: 30 Watts

• DC Output Protection: Auto Resetting PTC

• Rechargeable Battery Size: Max. 12 Ah

• Low Battery Cutoff Threshold: ~10 Volts.

• Load Regulation: + / - 2%

• Lifetime Limited Warranty

7 62158 10212 7

ELK-P212S

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 39 40

Comentários a estes Manuais

Sem comentários

Clipsal 56011 Especificações Página 19

Comentários a estes Manuais