Clipsal C-Bus2 Especificações Página 60
- Página / 120
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
C-BUS TRAINING MANUAL - VOL 2
60
2.2.4 Ramp 2
This parameter gives the time taken to ramp a light from minimum to maximum brightness (or vice
versa), using the Ramp Off or Ramp Recall Key Commands.
The default value is 12 seconds.
2.2.5 Status Report
Wired C-Bus
®
uses a status reporting system (known as an MMI), which provides automatic
detection and correction of discrepancies between the states of grouped inputs and outputs. This
status reporting occurs at periodic intervals. Increasing the frequency of status reporting decreases
the response time in which errors are corrected. However, it increases the amount of Network
communication traffic. If different status report values exist in the same Network, the smallest value is
used.
The default value is 3 seconds.
2.2.6 Learn Mode
Option Description
Allow Current
Application Learn
Determines whether learn mode can be used to group channels with other
units of the same Application Address.
Allow Any
Application Learn
Determines whether learn mode can be used to group channels with other
units of any Application Address. When grouping channels of units with
different Application Addresses using learn mode, the Application Addresses
of all units being included in the group will be changed to that of the unit
from which learn mode is exited.
Unit Has Learned This indicates that the unit has been involved in a learn mode operation.
Table 4 – Learn mode options
2.2.7 Disable All Keys
Allows the specication of a Group Address in the Enable Control application, which can be used to
disable all keys on this Key Unit.
2.2.8 Infra-red Setting
Allows the selection of Infra-red remote controls to use with this unit.
- Basic 1
- Training Manual 1
- Volume 2 1
- Contents Volume 2A. C-Bus 3
- Contents Volume 2D. DLT 6
- Volume 2A 9
- C-Bus Toolkit Software 9
- Learning Outcomes 10
- 1.0 PC Requirements 11
- 1.1 Hardware Requirements 11
- 1.2 Operating System 11
- 2.0 Installing the Software 12
- Installation Package 12
- 2.1 Starting the Program 13
- 3.0 The Menu 14
- 3.1.5 Preferences 15
- Advanced Tab 16
- 3.1.8 Exit 16
- 3.2 Projects Menu 17
- 3.3 Help Menu 17
- Figure 8 – Project Manager 18
- 4.1 Project 19
- 4.2 Network 20
- 4.3 Applications 20
- Icon Function 21
- 4.5 Groups 23
- 4.7 Units 25
- 4.8 Topology 27
- Network 28
- Figure 19 - Default Interface 29
- Figure 22 - Open Project 30
- Figure 23 - Add new project 30
- Figure 24 - Scanned Network 31
- Figure 25 - Transfer Units 32
- is ready to be programmed 33
- Volume 2B 34
- Basic Programming 34
- 1.0 Basic Learn Mode 36
- 1.1 Learn Mode Operations 37
- 1.1.4 Area Address Switching 38
- 1.1.5 Timer Congurations 38
- 1.2 Super Learn Mode 39
- 2.0 Voltage Free Relay 40
- 3.0 C-Bus 41
- Wall Switch 41
- 3.1 Functions 41
- Function Action 42
- 4.0 C-Bus 43
- Light Level Sensor 43
- 4.1 Groups 43
- 4.2 Ambient light 43
- 4.3 Target 44
- 5.0 C-Bus 45
- PIR Occupancy Sensor 45
- 5.4 Sunset to Sunrise 46
- 5.5 Security Features 46
- 5.6 Functions Tab 47
- Volume 2C 48
- Advanced Programming 48
- 1.0 Voltage Free Relay 50
- 1.1 Unit Identification 51
- 1.2 Logic 52
- 1.3 Turn On 53
- 1.4 Recovery 54
- 1.5 Restrike Delay 55
- 1.6 Global 56
- 1.7 Status 57
- 2.0 Neo 58
- 2.2 Global Tab 59
- Option Description 60
- Table 4 – Learn mode options 60
- 2.3 Power Fail Tab 61
- 2.4 Key Functions Tab 62
- 2.5 Blocks Tab 65
- 2.6 Indicators Tab 66
- 2.6.3 Enable Night Light 67
- 2.6.5 Enable ID Backlight 67
- 2.6.6 Enable Timer Flash 67
- 2.7 Scenes Tab 68
- 2.8 Environment Tab 69
- 2.9 StatusTab 70
- 3.0 Scene Control 71
- 3.2 Programming the Neo 72
- 2C. Advanced Programming 73
- Figure 22 – The Scene Manager 74
- Volume 2D 78
- Dynamic Labelling 78
- 1.1 Introduction 80
- 1.2 Programming the DLT 80
- 1.3 About DLT Broadcasting 80
- 2.0 DLT GUI 81
- 2.1 Global tab 82
- 2.2 Blocks tab 83
- 2.3 Indicators Tab 84
- 3.0 About DLT Units 85
- 3.1 Labelling Groups 85
- 3.2 Labelling Scenes 87
- 4.0 Setting the Time 88
- Volume 2E 90
- Network Bridges 90
- 1.1 Capabilities 93
- 1.2 Limitations 93
- 1.3 Construction 94
- 2.0 Network Topology 95
- 2.1 Daisy Chain 95
- 2.2 Star 96
- 2.3 Combination 97
- 3.0 Multi-Network Project 98
- Figure 6 - Network Details 99
- Figure 7 - CNI Network Setup 100
- 3.2 Add additional Networks 101
- C-BUS TRAINING MANUAL - VOL 2 102
- 2E. Network Bridges 103
- 4.0 Network Bridge GUI 105
- 4. 1 Connection Tab 106
- 4.3 Connect Applications 106
- 4.4 Message Destination 106
- 5.0 Group Addresses 107
- 5.1 Copy Tags 108
- Volume 2F 110
- Fault Finding 110
- 1.0 Fault Finding Chart 112
- 2F. Fault Finding 113
- 1.1 Fault Finding Notes 114
- Volume 2A. C-Bus 116
- Toolkit Software 116
- Volume 2B. Basic Programming 116
- Volume 2F. Fault Finding 119
- 1300 2025 25 120
- 1300 2025 56 120
- © Clipsal Australia Pty Ltd 120
Manuais e produtos relacionados com Monitor tátil Clipsal C-Bus2
Monitor tátil Clipsal C-Bus Guia do Utilizador
(60 páginas)
(60 páginas)
Monitor tátil Clipsal C-Bus Manual do Utilizador
(15 páginas)
(15 páginas)
Monitor tátil Clipsal C-Touch Guia do Utilizador
(20 páginas)
(20 páginas)
Monitor tátil Clipsal C-Bus2 Manual de Serviço
(24 páginas)
(24 páginas)
Monitor tátil Clipsal C-Bus Manual do Utilizador
(8 páginas)
(8 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.020 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais